THERMAL SCIENCE
International Scientific Journal
WOOL DRYING PROCESS IN HEAT-PUMP-ASSISTED DRYER BY FUZZY LOGIC MODELLING
ABSTRACT
The drying process in the textile industry is an expensive and laborious process that requires a lot of energy. The main purpose of the drying process is to provide maximum energy saving and energy efficiency at minimum time and cost without compromising the quality and structural properties of the material used. Since heat pumps are devices that can produce more heat compared to the work they consume, energy consumption substantially reduce is important. In drying processes, which are widely used in agriculture and textile industry in our country. It is important to use a heat pump in terms of energy saving. In this study, wool drying process in a heat-pump-assisted dryer was investigated with fuzzy logic metods. The test material used was wet wool, which is a fibrous material. The air velocities at the inlet of the dryer were varied from 0.8 m/s to 1.5 m/s, while the material loading ratio (material/dryer volume) ranged from 0.5 to 2.5. The temperature at the inlet of the dryer were varied from 40°C to 90°C. In this study, a fuzzy model was created to determine the effect of time, temperature, loading ratio and air velocity on the drying rate by using the fuzzy logic method, which is one of the artificial intelligence methods.
KEYWORDS
PAPER SUBMITTED: 2022-08-15
PAPER REVISED: 2023-02-01
PAPER ACCEPTED: 2023-04-07
PUBLISHED ONLINE: 2023-09-17
THERMAL SCIENCE YEAR
2023, VOLUME
27, ISSUE
Issue 4, PAGES [3043 - 3050]
- Strommen, I., et al., Atmospheric Freeze Drying With Heat Pumps - A New Alternative for High Quality Dried Food Products, Proceedings, 3rd Nordic Drying Conference, Karlstad, Sweden, 2005
- Soylemez, M. S., Optimum Heat Pump in Drying Systems with Waste Heat Recovery, J. Food Eng., 3 (2006), 74, pp. 292-298
- Ameen, A., Bari, S., Investigation Into the Effectiveness of Heat Pump Assisted Clothes Dryer for Humid Tropics, Energy Convers Manage, 45 (2004), 9-10, pp. 1397-1340
- Adapa, P. K., Schoenau, G. J., Recirculating Heat Pump Assisted Continuous Bed Drying and Energy Analysis, Int. J. Energy Res., 29 (2005), 11, pp. 961-972
- Fatouh, M., et al., Herbs Drying Using a Heat Pump Dryer, Energy Convers Manage, 47 (2006), 15-16, pp. 2629-2643
- Colak, N., Hepbasli, A., Exergy Analysis of Drying of Apple in a Heat Pump Dryer, Proceedings, 2nd International Conference of the Food Industries & Nutrition Division on; Future Trends in Food Science and Nutrition, Karlstad, Sweden, 2005, pp. 145-158
- Colak, N., Hepbasli, A., A Review of Heat Pump Drying: Part 1 - Systems, Models and Studies, Energy Conversion and Management, 50 (2009), 9, pp. 2180-2186
- Chua, K. J., et al., Heat Pump Drying: Recent Developments and Future Trends, Dry Technol., 20 (2002), 8, pp. 1579-15610
- Akarslan, F., The Effect of Textile Product Properties on Drying Efficiency, M. Sc. Thesis, Mechanical Engineering Department, Suleyman Demirel University, Isparta, Turkey, 2002
- Clements, S., et al., Experimental Verification of a Heat Pump Assisted Continuous Dryer Simulation Model, Int. J. Energy Res., 17 (1993), 1, pp. 19-28.
- Ceylan, I., et al., Energy and Exergy Analysis of Timber Dryer Assisted Heat Pump, Appl. Therm. Eng., 27 (2007), 1, pp. 216-222
- Colak, N., Hepbasli, A., A Review of Heat-Pump Drying (HPD): Part 2 - Applications and Performance Assessments, Energy Conversion and Management, 50 (2009), 9, pp. 2187-2199
- Hawlader, M. N. A., et al., A Simulation and Performance Analysis of a Heat Pump Batch Dryer, In: Mujumdar AS, Series Editor. Proceedings, 11th International Drying Symposium, Halkidiki, Greece, pp. 208-215, 1998
- Isin, D., Computer Simulation of a Solar Assisted Heat Pump System, M. Sc. Thesis, Mechanical Engineering Department, Middle East Technical University, Ankara, Turkey, 1991
- Jia, X., et al., Heat Pump Assisted Continuous Drying Part 2: Simulation Results, Int. J. Energy Res., 14 (1990), 7, pp. 771-782
- Jolly, P., et al., Heat Pump Assisted Continuous Drying Part 1: Simulation Model, Int. J. Energy Res., 14 (1990), 7, pp. 757-770
- Storslett, E., Experimental Investigation of a Heat Pump Assisted Drum Drying System Using Propane (R290) as Working Fluid, M. Sc. thesis, Norwegian University of Science and Technology, Energy and Process Engineering, Trondheim, Norwey, 2018
- Hosseinpour, S., Martynenko, A., Application of Fuzzy Logic in Drying: A Review, Drying Technology, 40 (2022), 5, pp. 797-826
- Ulkir, O., et al., Production of Piezoelectric Cantilever Using MEMS-Based Layered Manufacturing Technology, Optik, 273 (2023), Feb., 170472
- Vural, E., Ozer, S., Thermal Analysis of a Piston Coated with SiC and MgOZrO2 Thermal Barrier Materials, International Journal of Scientific and Technological Research, 1 (2015), 7, pp. 43-51
- Vural, E., et al., Analyzing the Effects of Hexane and Water Blended Diesel Fuels on Emissions and Performance in a Ceramic-Coated Diesel Engine by Taguchi Optimization Method, Fuel, 344 (2023), July, 128105
- Zadeh, L., Fuzzy Sets, Information and Control, 8 (1965), 3, pp. 338-3538
- Mamdani, E., Assilian, S., An Experiment in Linguistic Synthesis with a Fuzzy Logic Controller, International Journal of Man-Machine Studies, 7 (1975), 1, pp. 1-13
- Adeyi, O., et al., Adaptive Neuro Fuzzy Inference System Modeling of Synsepalum Dulcificum L. Drying Characteristics and Sensitivity Analysis of the Drying Factors, Scientific Reports, 12 (2022), 1, 13261
- Li, J., et al., Fuzzy Logic Control of Relative Humidity in Microwave Drying of Hawthorn, Journal of Food Engineering, 310 (2021), Dec., 110706
- Jahedi, R., et al., Fuzzy Logic, Artificial Neural Network and Mathematical Model for Prediction of White Mulberry Drying Kinetics, Heat and Mass Transfer, 54 (2018), May, pp. 3361-3374
- Li, J., et al., A Recurrent Self-Evolving Fuzzy Neural Network Predictive Control for Microwave Drying Process, Drying Technology, 34 (2016), 12, pp. 1434-1444
- Mansor, H., et al., Intelligent Control of Grain Drying Process Using Fuzzy Logic Controller, Journal of Food, Agriculture & Environment, 8 (2010), 2, pp. 145-149