THERMAL SCIENCE

International Scientific Journal

Thermal Science - Online First

online first only

Thermal management evaluation of the complex electro-optical system

ABSTRACT
The thermal management of a complex electro-optical system aimed for outdoor application is challenging task due to the requirement of having an air-sealed enclosure, harsh working environment and an additional thermal load generated by sunlight. It is essential to consider the effect of heating loads in the system components, as well as the internal temperature distribution, that can have influence on the system life expectancy, operational readiness and parameters, and possibility for catastrophic failure. The main objective of this paper is to analyze internal temperature distribution and evaluate its influence on system component operation capability. The electro-optical system simplified model was defined and related thermal balance simulation model based on Solid Works thermal analysis module was set and applied for temperature distribution calculation. Various outdoor environment scenarios were compared to evaluate system temperature distribution and evaluate its influence on system operation, reliability, and life time in application environment. This work was done during the design process as a part of the electro-optical system optimization. The results show that temperature distribution will not be cause for catastrophic failure and malfunction operation during operation in the expected environment.
KEYWORDS
PAPER SUBMITTED: 2016-03-28
PAPER REVISED: 2016-10-17
PAPER ACCEPTED: 2016-10-18
PUBLISHED ONLINE: 2016-11-06
DOI REFERENCE: https://doi.org/10.2298/TSCI160328260N
REFERENCES
  1. Anandan S. S., Ramalingam, V., Thermal Management of Electronics: A Review of literature, Thermal Science: 12 (2008), 2, pp. 5-26
  2. Shende D. M., Mahalle A., Cooling Of Electronic Equipment with Heat Sink: A Review of Literature, IOSR Journal of Mechanical and Civil Engineering(IOSR-JMCE), 5, (2013), 2, pp. 56-61
  3. Remsburg R., Thermal design of electronic equipment, CRC Press LLC, Boca Raton, Florida 33431, USA, 2001
  4. Jamnia A., Practical Guide to the Packaging of Electronics: Thermal and Mechanical Design and Analysis, Marcel Dekker Inc., New York, USA, 2003
  5. Kreith F. (Editor), The CRC handbook of thermal engineering, CRC Press LLC, Boca Raton, Florida 33431, USA, 2000
  6. Wankhede M., Khaire V., Manhandar A., Mahajan S.D., Evaluation of Cooling Solutions for Outdoor Electronics, Proceedings of 13th International Workshop on Thermal Investigation of ICs and Systems (THERMINIC), Budapest, Hungary, 2007, pp. 162-167
  7. Heindenen R., Karjalaihen M., Lankinen R., Verification of the thermal design of electronic equipment, VTT publication 320, VTT Technical Research Centre of Finland, 1997
  8. ASHRAE - American Society of Heating, Refrigerating and Air-Conditioning Engineers, IT Equipment Thermal Management and Controls, ASHRAE technical report, TC 9.9, USA, 2012
  9. (Ed. Zissis G.), The Infrared and Electro-Optical Systems Handbook, Vol 1. "Sources of Radiation", SPIE Optical Engineering Press, Bellingham, Washington, 1993
  10. Hsu, C.-N., et al., Heat Transfer and Structure Stress Analysis of Micro Packaging of micro packaging component of high power light emitting diode, Thermal Science, 17(2013), 5, pp. 1277-1283
  11. MIL-HDBK-338B - Electronic Reliability Design Handbook, US Department of Defence, USA, 1998
  12. MIL-HDBK-217F - Reliability Prediction of Electronic Equipment, US Department of Defence, USA, 1991
  13. ORE B 106/RP 12, Standardisation of coaches, Standardisation of a block-bracked solid wheel (tread diameter 920mm) for coaches with a top speed of 160 km/h, Basic calculations, Utrecht, 1989
  14. ERRI B 169/RP 8, Standardisation des essieux Determination de la tenacite des rouesmonoblocen R7, Definition d` unemethoded`essai et d` un critered`acceptation, (engl. Determination of toughness of mono block wheel R7, Definition a method of calculation and acceptation criteria),Utrecht, 1995
  15. Wang T., Ma S., TEG heat performance study about improved fin structures, Thermal Science, published online: 2016-04-09, DOI:10.2298/tsci150801064w
  16. Fok S.C., Tan F.L., Sua C.C., Experimental investigations on the cooling of a motorcycle helmet with phase change material, Thermal Science, 15(2011), 3, pp. 807-816
  17. Hsu C.-N., Chang Y.-H., Liu, C.-Y., Fang S.-H., Huang C.-C., Heat transfer and structure stress analysis of micro packaging component of high power light emitting diode, Thermal Science, 17(2013), 5, pp. 1277-1283
  18. Sivasankaran H., Asirvatham G., Bose J., Albert B., Experimental analysis of parallel plate and crosscut pin fin heat sinks for electronics cooling applications, Thermal Science, 14(2010), 1, pp. 147-156