THERMAL SCIENCE

International Scientific Journal

Thermal Science - Online First

Xiaoning Mao

,

Zhendong Liu

,

Liting Li

,

Shangzhi Yu

,

Qinglong Xie

,

Ying Duan

,

Yong Nie

online first only

Heat transfer characteristics of micro-droplet impacting on high-temperature wall in pyrolysis of methyl ricinoleate

ABSTRACT
The rapid heating of the material is a key factor in the pyrolysis of methyl ricinoleate, which is mainly affected by the droplet size and velocity of methyl ricinoleate droplet impacting on high-temperature wall. The process of millimeter-droplet of methyl ricinoleate impacting on high-temperature wall at different droplet sizes and velocities were studied by high-speed photography technology and multiphysics simulation. The simulation results were basically consistent with the experimental results. Based on this model, the process of micro-droplet impacting on high-temperature wall was investigated, obtaining the heat rates of droplet at different droplet sizes and velocities. The processes of 38 ~ 58 μm droplet impacting on high-temperature wall at velocity of 10 ~ 30 m/s were investigated. As the droplet at the initial temperature of 27 °C and droplet size of 38 μm impacting on a high-temperature wall of 480 °C at a speed of 20 m/s, the average heating rate of the droplet reached 107 ℃/s orders of magnitude. The results showed that faster heating rates were obtained at smaller droplet size and faster droplet velocity. Hence, the rapid heating of the material can be achieved by the micro-droplet impacting on stable high-temperature wall.
KEYWORDS
droplet impinging, phase field, micro-droplet, simulation, methyl ricinoleate
PAPER SUBMITTED: 2024-07-28
PAPER REVISED: 2024-10-11
PAPER ACCEPTED: 2024-10-12
PUBLISHED ONLINE: 2024-11-09
DOI REFERENCE: https://doi.org/10.2298/TSCI240728247M
REFERENCES
  1. Pereira, E.G., et al., Sustainable Energy: A Review Of Gasification Technologies, Renew. Sustain. Energy Rev., 16 (2012), 7, pp. 4753-4762
  2. Han, G., et al., Study Of Reaction And Kinetics In Pyrolysis Of Methyl Ricinoleate, J. Am. Oil Chem. Soc., 73 (1996), 9, pp. 1109-1112
  3. Hu, H.B., et al., Optimization of Production Temperatures of Heptaldehyde and Methyl Undecenoate from Methyl Ricinoleate by Pyrolysis Process, J. Ind. Eng. Chem., 6 (2000), 4, pp. 238-241
  4. Botton, V., et al., Thermal Cracking of Methyl Esters in Castor Oil and Production of Heptaldehyde and Methyl Undecenoate, J. Anal. Appl. Pyrolysis, 121 (2016), pp. 387-393
  5. Xu, B., et al., Experimental Study on Heat Transfer Characteristics of High-Temperature Heat Pipe, Therm. Sci., 26 (2022), 6, pp. 5227-5237
  6. Nie, Y., et al., Microwave-Assisted Pyrolysis of Methyl Ricinoleate for Continuous Production of Undecylenic Acid Methyl Ester (UAME), Bioresour. Technol., 186 (2015), pp. 334-337
  7. Mao, X., et al., Fast Pyrolysis of Methyl Ricinoleate in an Inductively Heated Reactor Coupled with Atomization Feeding, Appl. Therm. Eng., 194 (2021), 2, pp. 117093
  8. Yu, S., et al., Pyrolysis of Methyl Ricinoleate by Microwave-Assisted Heating Coupled with Atomization Feeding, J. Anal. Appl. Pyrolysis, 135 (2018), 9, pp. 176-183
  9. Yu, S., et al., Heat Transfer in a Novel Microwave Heating Device Coupled with Atomization Feeding, Therm. Sci., 26 (2022), 2A, pp. 1185-1195
  10. Mao, X., et al., Predictive Models for Characterizing the Atomization Process in Pyrolysis of Methyl Ricinoleate, Chinese J. Chem. Eng., 28 (2020), 4, pp. 1023-1028
  11. Yu, S., et al., Three-Dimensional Simulation of a Novel Microwave-Assisted Heating Device for Methyl Ricinoleate Pyrolysis, Appl. Therm. Eng., 153 (2019), March, pp. 341-351
  12. Mao, X., et al., Pyrolysis of Methyl Ricinoleate : Distribution and Characteristics of Fast and Slow Pyrolysis Products, Materials (Basel)., 15 (2022), pp. 1565
  13. Liu, H., et al., Thermodynamic Model And Kinetic Compensation Effect of Oil Sludge Pyrolysis Based on Thermogravimetric Analysis, Therm. Sci., 26 (2022), 1, pp. 259-272
  14. Abedinejad, M.S., Analysis of Spray Evaporation in a Model Evaporating Chamber: Effect of Air Swirl, J. Therm. Sci., 32 (2023), 2, pp. 837-853
  15. Silk, E.A., et al., Spray Cooling Heat Transfer: Technology Overview and Assessment of Future Challenges for Micro-Gravity Application, Enenegy Convers. Manag., 49 (2008), 3, pp. 453-468
  16. Lamini, O., et al., Experimental Study on the Effect of The Liquid/Surface Thermal Properties on Droplet Impact, Therm. Sci., 25 (2021), 1 Part B, pp. 705-716
  17. Liang, G., Mudawar, I., Review of Drop Impact on Heated Walls, Int. J. Heat Mass Transf., 106 (2017), pp. 103-126
  18. Misyura, S.Y., Morozov, V.S., Droplet Evaporation on a Heated Structured Wall, Therm. Sci., 23 (2019), 2, pp. 673-681
  19. Li, J., et al., Deposition Process of Droplets Impacting on a Horizontal Surface, Adv. Mater. Res., 354-355 (2012), pp. 579-584
  20. Negeed, E.S.R., et al., Dynamic Behavior of Micrometric Single Water Droplets Impacting onto Heated Surfaces with TiO2 Hydrophilic Coating, Int. J. Therm. Sci., 79 (2014), pp. 1-17
  21. Li, C., et al., A Heat Transfer Model for Aluminum Droplet/Wall Impact, Aerosp. Sci. Technol., 97 (2020), pp. 105639
  22. Alhashem, A., Khan, J., Heat Transfer Analysis for Dropwise-Filmwise Hybrid Surface of Steam on Vertical Plate, J. Therm. Sci., 30 (2021), 3, pp. 962-972
  23. Liang, G., et al., Single-Phase Heat Transfer of Multi-Droplet Impact on Liquid Film, Int. J. Heat Mass Transf., 132 (2019), pp. 288-292
  24. Zhang, B., et al., Numerical Simulation of Droplet Impinging Icing Process on a Low Temperature Wall with Smoothed Particle Hydrodynamics Method, Therm. Sci., 26 (2022), 4, pp. 3373-3385
  25. Zhang, R., et al., Analysis of Mist/Air Film Cooling Performance of Trenched Holes with Shaped Lips, Therm. Sci., 27 (2023), 4, pp. 2639-2649
  26. Tanguy, S., Berlemont, A., Application of a Level Set Method For Simulation of Droplet Collisions, Int. J. Multiph. Flow, 31 (2005), 9, pp. 1015-1035
  27. Shen, M., Li, B.Q., A Phase Field Approach to Modeling Heavy Metal Impact in Plasma Spraying, Coatings, 12 (2022), 10
  28. Park, Y.J., et al., Adhesion and Rheological Properties of EVA-Based Hot-Melt Adhesives, Int. J. Adhes. Adhes., 26 (2006), 8, pp. 571-576
  29. Cahn, J.W., On Spinodal Decomposition, Acta Metall., 9 (1961), 9, pp. 795-801
  30. Moon, J.H., et al., Dynamic Wetting and Heat Transfer Characteristics of a Liquid Droplet Impinging on Heated Textured Surfaces, Int. J. Heat Mass Transf., 97 (2016), pp. 308-317
  31. Visser, C.W., et al., Microdroplet Impact at Very High Velocity, Soft Matter, 8 (2012), 41, pp. 10732-10737
  32. Zhang, Z., et al., Numerical Study on Dynamic Behaviours of a Micro-Droplet Impacting on a Vertical Wall In PEMFC, Int. J. Hydrogen Energy, 46 (2021), 35, pp. 18557-18570
PDF VERSION [DOWNLOAD]
Heat transfer characteristics of micro-droplet impacting on high-temperature wall in pyrolysis of methyl ricinoleate