THERMAL SCIENCE

International Scientific Journal

EXPERIMENTAL STUDY ON COLLABORATIVE ENHANCEMENT OF LED HEAT DISSIPATION CHARACTERISTICS BY PULSATING HEAT PIPE AND HEAT PIPE

ABSTRACT
The objective of this research is to experimentally evaluate the specific impact of a collaborative heat sink composed of gravity heat pipes (GHP) and pulsating heat pipes (PHP) on the thermal efficiency of LED light sources. The heat sink developed in this experiment is designed to improve the thermal management system, ensuring that LED operate within a safe temperature range, which is crucial as the performance of LED is directly affected by their junction temperature. An HP-PHP collaborative heat sink was employed in the experiment, where PHP served as heat dissipating fins to enhance its thermal performance, while HP handles the majority of the heat transfer tasks. The results showed that under forced convection conditions, the HP-PHP collaborative heat sink can increase the maximum thermal power capacity of LED to 192 W. The HP-PHP collaborative heat sink can reduce the substrate’s temperature to below 70.5 °C in passive mode when the LED input power does not exceed 96 W. Additional experimental results show that the minimum thermal resistance of the collaborative heat sink is 0.19 K/W under natural-convection conditions, under forced convection conditions, this value drops to 0.15 K/W, which still lower than the non-collaborative heat sink. These results demonstrate that the contact thermal resistance between HP and PHP significantly enhances the thermal performance of the collaborative heat sink. Therefore, this collaborative type of heat sink is an effective method for cooling high power LED.
KEYWORDS
PAPER SUBMITTED: 2023-08-28
PAPER REVISED: 2023-11-24
PAPER ACCEPTED: 2023-11-26
PUBLISHED ONLINE: 2024-02-18
DOI REFERENCE: https://doi.org/10.2298/TSCI230828010S
CITATION EXPORT: view in browser or download as text file
THERMAL SCIENCE YEAR 2024, VOLUME 28, ISSUE Issue 3, PAGES [2491 - 2500]
REFERENCES
  1. Cho, J., et al., Efficiency Droop in Light-Emitting Diodes: Challenges And Countermeasures, Laser and Photonics Reviews, 7 (2013), 3, pp. 408-421
  2. Hsieh, C.-C., et al., Modular Design of the LED Vehicle Projector Headlamp System, Appl. Opt., 52 (2013), 21, 5221
  3. Yang, K., et al., Thermal Analysis and Design of High-Power LED Street Light, Proceedings, Symposium on Photonics and Optoelectronics, Chengdu, China, 2010, pp. 1-4
  4. Narendran, N., Gu, Y., A Loop-Heat-Pipe Heat Sink with Parallel Condensers for High-Power Integrated LED Chips, Journal Display Technol., 1 (2005), 1, pp. 167-171
  5. Luo, X., et al., Experimental and Numerical Study on a Micro Jet Cooling Solution for High Power LED, Sci. China Ser. E, 50 (2007), 4, pp. 478-489
  6. Kang, X., et al., Phase-Change Immersion Cooling High Power Light Emitting Diodes and Heat Transfer Improvement, Microelectronics Reliability, 79 (2017), Dec., pp. 257-264
  7. Ye, H., et al., Two-Phase Cooling of Light Emitting Diode for Higher Light Output and Increased Efficiency, Applied Thermal Engineering, 52 (2013), 2, pp. 353-359
  8. Kim, L., et al., Thermal Analysis of LED Array System with Heat Pipe, Thermochimica Acta, 455 (2007), 1-2, pp. 21-25
  9. Lai, C., et al., Thermal Performance of An Indoor Oblong LED Lighting Prototype Incorporating Heat Pipes, Journal of Asian Architecture and Building Engineering, 8 (2009), 2, pp. 585-592
  10. Lu, X., et al., Thermal Analysis of Loop Heat Pipe Used for High-Power LED, Thermochimica Acta, 493 (2009), 1-2, pp. 25-29
  11. Lu, X., et al., Thermal Analysis of High Power LED Package with Heat Pipe Heat Sink, Microelectronics Journal, 42 (2011), 11, pp. 1257-1262
  12. c, L., et al., A Robust Pulsating Heat Pipe Cooler for Integrated High Power LED Chips, Heat Mass Transfer, 53 (2017), 11, pp. 3305-3313
  13. Maydanik, Y. F., et al., Compact Cooler for Electronics on the Basis of a Pulsating Heat Pipe, Applied Thermal Engineering, 29 (2009), 17-18, pp. 3511-3517
  14. Li, J., et al., A Loop-Heat-Pipe Heat Sink With Parallel Condensers for High-Power Integrated LED Chips, Applied Thermal Engineering, 56 (2013), 1-2, pp. 18-26
  15. Xu, Z., Thermal Performance and Multi-Objective Optimization of Thermosyphon Heat Sinks with Rectangular Radial Fins for High Power LED Lamps Cooling, Case Studies in Thermal Engineering, 30 (2022), 101778

© 2024 Society of Thermal Engineers of Serbia. Published by the Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, Belgrade, Serbia. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International licence