ABSTRACT
Li-ion batteries are widely used in electric vehicles for their superior performance. To investigate a simple and efficient method for the Li-ion power batteries, the cold plate with four types of structures A, B, C, and D were established, respectively. Subsequently, the effects of micro-channel thickness and width on the cooling performance of battery thermal management systems were analyzed by using a numerical simulation method. The results show that with the increases of the micro-channel thickness, the maximum temperature (Tmax) of the cold plate is gradually increased under structures A, B, and C, while it is gradually decreased under structure D. The standard deviation of temperature (Tσ) of the cold plate of structure A was less affected by the change of the micro-channel thickness. Under structures B, C, and D, the temperature uniformity of the cold plate can be well maintained when the micro-channel thickness was 1.0 [mm]. With the increase of the micro-channel width, the Tmax and Tσ of the cold plate are gradually increased in all cases, while the ΔP from the inlet to outlet is gradually decreased. The temperature uniformity of the cold plate is well maintained by structure C. The decreasing amount and changing range of ΔP caused by the change of micro-channel width is smaller than caused by the change of the thickness.
KEYWORDS
PAPER SUBMITTED: 2021-06-08
PAPER REVISED: 2021-08-27
PAPER ACCEPTED: 2021-10-18
PUBLISHED ONLINE: 2021-11-06
THERMAL SCIENCE YEAR
2022, VOLUME
26, ISSUE
Issue 2, PAGES [1503 - 1517]
- Bu, C., et al., Oxy-fuel combustion of a single fuel particle in a fluidized bed: Char combustion characteristics, an experimental study, Chemical Engineering Journal, 287. (2016), pp. 649-656, DOI No. doi.org/10.1016/j.cej.2015.11.078
- Fathabadi, H., A novel design including cooling media for Lithium-ion batteries pack used in hybrid and electric vehicles, Journal of Power Sources, 245. (2014), pp. 495-500, DOI No. doi.org/10.1016/j.jpowsour.2013.06.160
- Kang, B.H.,H.J. Lee, A Review of Recent Research on Automotive HVAC Systems for EVs, International Journal of Air-Conditioning and Refrigeration, 25. (2017), 4, DOI No. 10.1142/S2010132517300038
- Wada, M., Research and development of electric vehicles for clean transportation, Journal of Environmental Sciences, 21. (2009), 6, pp. 745-749, DOI No. doi.org/10.1016/S1001-0742(08)62335-9
- Lu, L., et al., A review on the key issues for lithium-ion battery management in electric vehicles, Journal of Power Sources, 226. (2013), pp. 272-288, DOI No. doi.org/10.1016/j.jpowsour.2012.10.060
- Zhao, X.Y., THERMAL PERFORMANCE ANALYSIS AND OPTIMAL CONTROL OF POWER LITHIUM CELL THERMAL MANAGEMENT SYSTEM FOR NEW ENERGY VEHICLES, Thermal Science, 24. (2020), 5, pp. 3375-3383, DOI No. 10.2298/tsci191220129z
- Sun, X.D., et al., RESEARCH ON THERMAL EQUILIBRIUM PERFORMANCE OF LIQUID-COOLED LITHIUM-ION POWER BATTERY SYSTEM AT LOW TEMPERATURE, Thermal Science, 24. (2020), 6, pp. 4147-4158, DOI No. 10.2298/tsci200118155s
- An, Z., et al., Experimental investigation on lithium-ion battery thermal management based on flow boiling in mini-channel, Applied Thermal Engineering, 117. (2017), pp. 534-543, DOI No. doi.org/10.1016/j.applthermaleng.2017.02.053
- Xie, J., et al., Structural optimization of lithium-ion battery pack with forced air cooling system, Applied Thermal Engineering, 126. (2017), pp. 583-593, DOI No. doi.org/10.1016/j.applthermaleng.2017.07.143
- Huo, Y., et al., Investigation of power battery thermal management by using mini-channel cold plate, Energy Conversion and Management, 89. (2015), pp. 387-395, DOI No. doi.org/10.1016/j.enconman.2014.10.015
- Wang, Z., et al., Paraffin and paraffin/aluminum foam composite phase change material heat storage experimental study based on thermal management of Li-ion battery, Applied Thermal Engineering, 78. (2015), pp. 428-436, DOI No. doi.org/10.1016/j.applthermaleng.2015.01.009
- Saw, L.H., et al., Computational fluid dynamic and thermal analysis of Lithium-ion battery pack with air cooling, Applied Energy, 177. (2016), pp. 783-792, DOI No. doi.org/10.1016/j.apenergy.2016.05.122
- Fang, Y., et al., Investigation on the Transient Thermal Performance of a Mini-Channel Cold Plate for Battery Thermal Management, Journal of Thermal Science. (2020), 5
- Wang, J., et al., Sensitivity analysis of factors influencing a heat pipe-based thermal management system for a battery module with cylindrical cells, Applied Thermal Engineering, 151. (2019), pp. 475-485, DOI No. doi.org/10.1016/j.applthermaleng.2019.02.036
- Xia, G., et al., A review on battery thermal management in electric vehicle application, Journal of Power Sources, 367. (2017), pp. 90-105, DOI No. doi.org/10.1016/j.jpowsour.2017.09.046
- Tang, A., et al., Optimization design and numerical study on water cooling structure for power lithium battery pack, Applied Thermal Engineering, 159. (2019), pp. 113760-
- Lee, M.-Y., et al., Thermal Abuse Behavior of the LIR2450 Micro Coin Cell Battery Having Capacity of 120 mAh with Internal Short Circuit by Penetrating Element, Symmetry, 12. (2020), 2, p. 246
- Deng, T., et al., Study on thermal management of rectangular Li-ion battery with serpentine-channel cold plate, International Journal of Heat and Mass Transfer, 125. (2018), pp. 143-152, DOI No. doi.org/10.1016/j.ijheatmasstransfer.2018.04.065
- Lan, C., et al., Thermal management for high power lithium-ion battery by minichannel aluminum tubes, Applied Thermal Engineering, 101. (2016), pp. 284-292, DOI No. doi.org/10.1016/j.applthermaleng.2016.02.070
- Dong, F., et al., Investigation of the effect of U-shaped mini-channel structure on the thermal performance of liquid-cooled prismatic batteries, Numerical Heat Transfer Applications, 77. (2019), 1, pp. 1-16