THERMAL SCIENCE

International Scientific Journal

Thermal Science - Online First

Taha Resul Karakus

,

Ilker Firat

,

Orhan Yildirim

,

Fatin Sonmez

,

Sevinc Sevgi Kocali

,

Abdussamed Yildiz

,

Sendogan Karagoz

,

Omer Comakli

online first only

Experimental investigation of thermal performance and entropy analysis of sphere turbulators

ABSTRACT
In this study, the effects of different numbers of sphere turbulators placed in a circular-shaped test pipe under turbulent flow conditions on heat transfer, friction factor, thermal performance factor and entropy production were experimentally investigated. Water was used as the working fluid in the experiments carried out in the number range Re=8379-16701. Initially, plain pipe and supported plain pipe experiments were carried out by keeping the fluid inlet temperature and test pipe surface temperature constant. Then, 1, 2 and 3 sphere turbulator experiments were carried out under the same conditions, respectively. According to the findings, the maximum Nusselt number increase compared to the supported plain pipe was 83.34% for the test pipe with 3 sphere turbulators. The minimum and maximum Nu number increase rates of 3 sphere turbulators compared to 1 and 2 sphere turbulators were obtained as 42.61%-46.93% and 13.99%-17.11%, respectively. The increase rates of maximum friction factors of 1, 2 and 3 sphere turbulators compared to the supported plain pipe were 174.42%, 226.70% and 306.53%, respectively. In addition, the maximum total entropy rate for sphere turbulators was obtained as 0.058 W.m-1.K-1 for 1 sphere turbulator at Re = 8379. In terms of the second law, the maximum entropy generation of sphere turbulators compared to the supported plain pipe decreased by 79.39% for 3 sphere turbulators at Re = 8379. As a result, it was concluded that the optimum number of sphere turbulators is 3 sphere turbulators with the lowest entropy production number and the highest TPF value (1.28).
KEYWORDS
turbulator, entropy, thermal performance, Reynolds number
PAPER SUBMITTED: 2024-03-04
PAPER REVISED: 2024-06-07
PAPER ACCEPTED: 2024-07-08
PUBLISHED ONLINE: 2024-08-18
DOI REFERENCE: https://doi.org/10.2298/TSCI240304165K
REFERENCES
  1. Yao, B., et al., Improving the thermal performance of the heat exchanger through simultaneous utilization of novel magnetic turbulators and helical coil wire turbulators, International Journal of Thermal Sciences, 197 (2024), 108812, doi: 10.1016/J.IJTHERMALSCI.2023.108812
  2. Sekulic, D. P., Shah, R. K., Fundamentals of Heat Exchanger Design, John Wiley and Sons Inc, 2024
  3. Kakaç, S., et al., Heat Exchangers: Selection, Rating, and Thermal Design, CRC Press, Second Edition, 2002
  4. Mashoofi, N., et al., Numerical study of heat transfer and exergy loss in a double tube heat exchanger with corrugated inner tube: the new configuration of corrugated tubes, Journal of Mechanical Engineering, 48 (2018), 3, pp. 301-307 (in Persian)
  5. Cheraghi, M. H., et al., Numerical study on the heat transfer enhancement and pressure drop inside deep dimpled tubes, Int J Heat Mass Transf, 147 (2020), 118845, doi: 10.1016/J.IJHEATMASSTRANSFER.2019.118845
  6. Amani, M., et al., The efficacy of magnetic field on the thermal behavior of MnFe2O4 nanofluid as a functional fluid through an open-cell metal foam tube, J Magn Magn Mater, 432 (2017), pp. 539-547, doi: 10.1016/J.JMMM.2017.02.045
  7. Asar, F. J., et al., Direct synthesis of piperazines containing dithiocarbamate derivatives via DABCO bond cleavage, Tetrahedron Lett, 61 (2020), 49, 152610, doi: 10.1016/J.TETLET.2020.152610
  8. Najmi, L., Hu, Z., Effects of carbon nanotubes on thermal behavior of epoxy resin composites, Journal of Composites Science, 7 (2023), 8, doi: 10.3390/jcs7080313
  9. Mashoofi, N., et al., Fabrication method and thermal-frictional behavior of a tube-in-tube helically coiled heat exchanger which contains turbulator, Appl Therm Eng, 111 (2017), pp. 1008-1015, doi: 10.1016/J.APPLTHERMALENG.2016.09.163
  10. Nakhchi, M. E., et al., Effects of CuO nano powder on performance improvement and entropy production of double-pipe heat exchanger with innovative perforated turbulators, Advanced Powder Technology, 32 (2021), 8, pp. 3063-3074, doi: 10.1016/J.APT.2021.06.020
  11. Bahuguna, R., et al., Entropy generation analysis in a tube heat exchanger integrated with triple blade vortex generator inserts, Energy Sources, Part A: Recovery, Utilization and Environmental Effects, 2021, doi: 10.1080/15567036.2021.1918291
  12. Maithani, R., Kumar, A., Correlations development for Nusselt number and friction factor in a dimpled surface heat exchanger tube, Experimental Heat Transfer, 33 (2020), 2, pp. 101-122, doi: 10.1080/08916152.2019.1573863
  13. Sheikholeslami, M., et al., Heat transfer of nanoparticles employing innovative turbulator considering entropy generation, Int J Heat Mass Transf, 136 (2019), 1233-1240, doi: 10.1016/J.IJHEATMASSTRANSFER.2019.03.091
  14. Sepehr, M., et al., Prediction of heat transfer, pressure drop and entropy generation in shell and helically coiled finned tube heat exchangers, Chemical Engineering Research and Design, 134 (2018), pp. 277-291, doi: 10.1016/J.CHERD.2018.04.010
  15. Farzaneh-Gord, M., et al., Tube-in-tube helical heat exchangers performance optimization by entropy generation minimization approach, Appl Therm Eng, 108 (2016), pp. 1279-1287, doi: 10.1016/J.APPLTHERMALENG.2016.08.028
  16. Salhi, J. E., et al., Numerical analysis of the properties of nanofluids and their impact on the thermohydrodynamic phenomenon in a heat exchanger, Mater Today Proc, 45 (2021), pp. 7559-7565, doi: 10.1016/J.MATPR.2021.02.365
  17. Salhi, J. E., et al., Analysis of the thermohydrodynamic behavior of a cooling system equipped with adjustable fins crossed by the turbulent flow of air in forced convection, International Journal of Energy and Environmental Engineering, 13 (2022), 3, pp. 1039-1051, doi: 10.1007/s40095-021-00446-5
  18. Salhi, J. E., et al., Turbulence and thermo-flow behavior of air in a rectangular channel with partially inclined baffles, Energy Sci Eng, 2022, doi: 10.1002/ese3.1239
  19. Salhi, J. E., et al., Numerical study of the thermo-energy of a tubular heat exchanger with longitudinal baffles, Mater Today Proc, 45 (2021), pp. 7306-7313, doi: 10.1016/J.MATPR.2020.12.1213
  20. Fang, Y., et al., Numerical study on heat and flow transfer characteristics in rectangular mini-channel with s-shaped turbulator inserted, Thermal Science, 27 (2023), 4, pp. 2865-2877, doi: 10.2298/TSCI220919210F
  21. Balan, V., et al., Investigation on the enhancement of heat transferin counterflow double-pipe heat exchangerusing nanofluids, Thermal Science, 28 (2024), 1A, pp. 233-240, doi: 10.2298/TSCI230312273V
  22. Selvam, S., et al., Experimental studies on effect of bonding the twisted tape with pins to the inner surface of the circular tube, Thermal Science, 18 (2014), 4, pp. 1273-1283, doi: 10.2298/TSCI120807036S
  23. Firat, I., et al., Performance and entropy production analysis of angle blade turbulators used to increase heat transfer, J Therm Anal Calorim, 148 (2023), 15, pp. 7811-7828, doi: 10.1007/s10973-023-12253-7
  24. Eiamsa-ard, S., Promvonge, P., Enhancement of heat transfer in a tube with regularly-spaced helical tape swirl generators, Solar Energy, 78 (2005), 4, pp. 483-494, doi: 10.1016/J.SOLENER.2004.09.021
  25. Goh, L. H. K., et al., Entropy generation analysis of turbulent convection in a heat exchanger with self-rotating turbulator inserts, International Journal of Thermal Sciences, 160 (2021), 106652, doi: 10.1016/j.ijthermalsci.2020.106652
  26. Firat, I., et al., Experimental investigation of the thermal performance effects of turbulators with different fin angles in a circular pipe, International Journal of Thermal Sciences, 184 (2023), 107969, doi: 10.1016/J.IJTHERMALSCI.2022.107969
  27. Karagoz, S., et al., Experimental investigation of the effect of wave turbulators on heat transfer in pipes, Thermal Science, 26 (2022), 2, pp. 1771-1783, doi: 10.2298/TSCI210206183K
  28. Kline, S. J., McClintock, F. A., Describing uncertainty in single sample experiments, Mech. Engineering, 75 (1953), pp. 3-8
  29. Salhi, J. E., et al., Numerical investigations of the impact of a novel turbulator configuration on the performances enhancement of heat exchangers, J Energy Storage, 46 (2022), 103813, doi: 10.1016/J.EST.2021.103813
  30. Turgut, E., Yardımcı, U., Comprehensive analysis of the performance of the coaxial heat exchanger with turbulators, International Journal of Thermal Sciences, 76 (2022), 107502, doi: 10.1016/J.IJTHERMALSCI.2022.107502
  31. Ghajar, A. J., et al., Experimental investigation of friction factor in the transition region for water flow in minitubes and microtubes, Heat Transfer Engineering, 31 (2010), 8, pp. 646-657, doi: 10.1080/01457630903466613
  32. Akyürek, E. F., et al., Experimental analysis for heat transfer of nanofluid with wire coil turbulators in a concentric tube heat exchanger, Results Phys, 9 (2018), pp. 376-389, doi: 10.1016/J.RINP.2018.02.067
  33. Sahin, B., et al., Experimental investigation of heat transfer and pressure drop characteristics of Al2O3-water nanofluid, Exp Therm Fluid Sci, 50 (2013), pp. 21-28, doi: 10.1016/J.EXPTHERMFLUSCI.2013.04.020
  34. Luo, J., et al., Thermal-frictional behavior of new special shape twisted tape and helical coiled wire turbulators in engine heat exchangers system, Case Studies in Thermal Engineering, 53 (2024), 103877, doi: 10.1016/J.CSITE.2023.103877
  35. Hong, Y., et al., Turbulent thermal, fluid flow and thermodynamic characteristics in a plain tube fitted with overlapped multiple twisted tapes, Int J Heat Mass Transf, 115 (2017), pp. 551-565, doi: 10.1016/J.IJHEATMASSTRANSFER.2017.08.017
  36. Kongkaitpaiboon, V., et al., Experimental investigation of heat transfer and turbulent flow friction in a tube fitted with perforated conical-rings, International Communications in Heat and Mass Transfer, 37 (2010), 5, pp. 560-567, doi: 10.1016/J.ICHEATMASSTRANSFER.2009.12.015
  37. Eiamsa-ard, S., et al., Convective heat transfer in a circular tube with short-length twisted tape insert, International Communications in Heat and Mass Transfer, 36 (2009), 4, pp. 365-371, doi: 10.1016/J.ICHEATMASSTRANSFER.2009.01.006
  38. Kaood, A., Fadodun, O. G., Numerical investigation of turbulent entropy production rate in conical tubes fitted with a twisted-tape insert, International Communications in Heat and Mass Transfer, 139 (2022), 106520, doi: 10.1016/J.ICHEATMASSTRANSFER.2022.106520
  39. Jayranaiwachira, N., et al., Entropy generation and thermal performance of tubular heat exchanger fitted with louvered corner-curved V-baffles, Int J Heat Mass Transf, 201 (2023), 123638, doi: 10.1016/J.IJHEATMASSTRANSFER.2022.123638
PDF VERSION [DOWNLOAD]
Experimental investigation of thermal performance and entropy analysis of sphere turbulators