THERMAL SCIENCE

International Scientific Journal

Authors of this Paper

External Links

COMPUTATIONAL FLUID DYNAMICS SIMULATION OF THE SUPERSONIC STEAM EJECTOR USING DIFFERENT CONDENSATION MODEL

ABSTRACT
This paper addresses the non-equilibrium condensation (NEC) in supersonic steam ejector under the assumptions of no slip velocity between the droplets and vapor phase and homogenous nucleation. The experimental data carried out by Moore has been used to verify the numerical results. It is illustrated that the maximum value of the flow mach number of the NEC model is lower than that of the equilibrium condensation model, and NEC model increases the ejector’s entrainment ratio in comparison equilibrium condesation model. When using the NEC model, the nucleation characteristics such as subcooling degree, nucleation rate could be obtained in ejector flow field.
KEYWORDS
PAPER SUBMITTED: 2018-07-23
PAPER REVISED: 2018-09-23
PAPER ACCEPTED: 2018-12-25
PUBLISHED ONLINE: 2019-05-26
DOI REFERENCE: https://doi.org/10.2298/TSCI180723236C
CITATION EXPORT: view in browser or download as text file
THERMAL SCIENCE YEAR 2019, VOLUME 23, ISSUE Issue 3, PAGES [1655 - 1661]
REFERENCES
  1. Keenan, J. H., et al.. An Investigation of Ejector Design by Analysis and Experiment, J. Appl. Mech. Trans. ASME, 72(1950), pp. 299-309
  2. Huang, B. J., et al.. Ejector Performance Characteristics and Design Analysis of Jet Refrigeration System, J. Eng. Power Trans. ASME, 107(1985), pp. 792-802
  3. Sriveerakul, T., et al.. Performance Prediction of Steam Ejector Using Computational Fluid Dynamics: Part 2. Flow Structure of a Steam Ejector Influenced by Oper-Ating Pressures and Geometries. Int. J. Therm. Sci., 46(2007), pp. 823-833
  4. Zheng, H. T., et al.. Computational Fluid Dynamics Simulation of the Supersonic Steam Ejector. Part 1: Comparative Study of Different Equations of State, Proc. IMechE Part C: J. Mechanical Engineering Science. 226(2012), pp. 709-714
  5. Cai, L., et al.. Computational Fluid Dynamics Simulation of the Supersonic Steam Ejector. Part 2. Optimal Design of Geometry and the Effect of Operating Conditions on the Ejector. Proc. IMechE Part C: J, Mechanical Engineering Science. 226(2012), pp. 709-714
  6. Bakhtar, F., et al.. On the Performance of a Cascade of Turbine Rotor Tip Section Blading in Wet Steam. Part 2: Surface Pressure Distributions. J. Mech. Eng. Sci. 211(2005), pp. 531-540
  7. Gyarmathy, G.. Bases of a Theory for Wet Steam Turbines (Ph.D. Thesis), Federal Technical University of Zurich, Swiss, 1962
  8. Young, J. B., et al., The Inertial Deposition of Fog Droplets on Steam Turbine Blades, J. Turbomach. 110(1988), pp. 155-162
  9. Yu, X. G., et al., Numerical Investigation of Condensing Flow in the Last Stage of Low-Pressure Nuclear Steam Turbine, Nuclear Engineering and Design, 275(2014), pp. 197-204
  10. Dykas, S., et al.. Predictions of Losses in the Flow through the Last Stage of Low-Pressure Steam Turbine, Int. J. Numer. Methods Fluids, 53(2006), pp. 933-945
  11. Moore, M. J., et al.. Predicting the Fog-Drop Size in Wet-Steam Turbines. Institute of Mechanical Engineering, 1974, 101-109
  12. Sharifi, N., et al., Numerical Assessment of Steam Nucleation on Thermodynamic Performance of Steam Ejectors, Applied Thermal Engineering, 52(2013), pp. 449-459

© 2024 Society of Thermal Engineers of Serbia. Published by the Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, Belgrade, Serbia. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International licence