THERMAL SCIENCE

International Scientific Journal

EFFECT OF GEOMETRICAL STRUCTURE OF EMBEDDED PHASE CHANGE MATERIAL ON THE POWER GENERATION OF THERMOELECTRIC MODULE

ABSTRACT
The effect of geometrical structure of embedded phase change material (PCM) on the power generation of the thermoelectric module (TEM) was studied in this work. Paraffin wax with different geometrical structure was embedded in a polymer container which is adhered to the hot junction of the fabricated TEM. Since the PCM can used as the heat source and provide latent heat when the heat source stops providing heat, applying the PCM in the TEM is an efficiency method to enhance the power generation of the TEM. Our experimental results show that the energy harvesting time becomes 60 seconds longer in comparison with the case without the PCM when 4.3 g weight of paraffin wax is applied. At the same time, the power generation of the TEM increases by magnitude of 25%. Moreover, the output voltage and electrical energy generation of TEM with PCM increase with increasing both cross-area and height of the applied PCM.
KEYWORDS
PAPER SUBMITTED: 2017-02-15
PAPER REVISED: 2017-06-30
PAPER ACCEPTED: 2017-07-29
PUBLISHED ONLINE: 2017-08-05
DOI REFERENCE: https://doi.org/10.2298/TSCI170215167A
CITATION EXPORT: view in browser or download as text file
THERMAL SCIENCE YEAR 2018, VOLUME 22, ISSUE Issue 6, PAGES [2691 - 2698]
REFERENCES
  1. Klimanek. A, Kostowski. W. J, Burda. G, et al. Preliminary design and modelling of a gas-fired thermoelectric generator. Thermal Science, 2016, Vol. 20, pp. 1233-1244
  2. B. A. Gupta, S. Chand, N. K. Patel, A. Soni. A review on thermoelectric cooler. International Journal for Innovative Research in Science & Technology, 2016, Vol. 2, pp. 674-679
  3. H. J. Goldsmid. Thermoelectric modules and their application. Introduction to Thermoelectricity, 2016, Vol. 121, pp. 197-220
  4. Kumar. R. C, Ankit. S, Rahul. G. Experimental study on waste heat recovery from an internal combustion engine using thermoelectric technology. Thermal Science, 2011, Vol. 15, pp. 1011-1022
  5. Y. Zhang, et al., High-temperature and high-power-density nanostructured thermoelectric generator for automotive waste heat recovery. Energy Conversion & Management, 2015, Vol. 105, pp. 946-950
  6. J. Yang, F. R. Stabler. Automotive applications of thermoelectric materials. Journal of Electronic Materials, 2009, Vol. 38, pp. 1245-1251
  7. M. N. Adroja, S. B. Mehta, M. P. Shah. Review of thermoelectricity to improve energy quality. International Journal of Emerging Technologies and Innovative Research, 2015, Vol. 2, pp. 847-850
  8. D. Tatarinov, et al., Modeling of a thermoelectric generator for thermal energy regeneration in automobiles. Journal of Electronic Materials, 2013, Vol. 42, pp.2274-2281
  9. G. Min. Thermoelectric module design under a given thermal input: theory and example. Journal of Electronic Materials, 2013, Vol. 42, pp.2239-2242
  10. J. De Boor, E. Müller. Data analysis for seebeck coefficient measurements. Review of Scientific Instruments, 2013, Vol. 84, 065102
  11. Saqr. K. M, Musa M. N. Critical review of thermoelectrics in modern power generation applications. Thermal Science, 2009, Vol. 13, pp. 165-174
  12. S. Twaha, J. Zhu, Y. Yan, B. Li. A comprehensive review of thermoelectric technology: materials, applications, modelling and performance improvement. Renewable and Sustainable Energy Reviews, 2016, Vol. 65, pp. 698-726
  13. Y. Wang, C. Dai, S. Wang. Theoretical analysis of a thermoelectric generator using exhaust gas of vehicles as heat source. Applied Energy, 2013, Vol. 112, pp.1171-1180
  14. Yoo. D. W, Joshi. Y. K. Energy efficient thermal management of electronic components using solid-liquid phase change materials. IEEE Transactions on Device & Materials Reliability, 2004, Vol. 4, pp. 641-649
  15. D. Samson, T. Otterpohl, M. Kluge, U. Schmid, T. Becker. Aircraft-specific thermoelectric generator module. Journal of Electronic Materials, 2009, Vol. 39, pp. 2092-2095
  16. C. K. Yoon, G. Chitnis, B. Ziaie. Impact-triggered thermoelectric power generator using phase change material as a heat source. Journal of Micromechanics and Microengineering, 2013, Vol. 23, 114004
  17. S. E. Jo, M. S. Kim, M. K. Kim, Y. J. Kim. Power generation of a thermoelectric generator with phase change materials. Smart Material Structures, 2013, Vol. 22, pp. 2870-2876.
  18. A. Elefsiniotis, T. Becker, U. Schmid. Thermoelectric energy harvesting using phase change materials (pcms) in high temperature environments in aircraft. Journal of Electronic Materials, 2013, Vol. 43, pp. 1809-1814
  19. A. Agbossou, Q. Zhang, G. Sebald, D. Guyomar. Solar micro-energy harvesting based on thermoelectric and latent heat effects. Part I: Theoretical analysis. Sensors and Actuators A: Physical, 2010, Vol. 163, pp. 277-283
  20. Q. Zhang, A. Agbossou, Z. Feng, M. Cosnier. Solar micro-energy harvesting based on thermoelectric and latent heat effects. Part II: Experimental analysis. Sensors and Actuators A: Physical, 2010, Vol. 163, pp. 284-290
  21. Q. Zhang, A. Agbossou, Z. Feng, A. C. Grillet. Phase change material and the thermoelectric effect for solar energy harvesting and storage. Proceedings of the asme/jsme 2011 8th thermal engineering joint conference, Hawaii, USA: 2011
  22. X. Q. Wang, A. S. Mujumdar, C. Yap. Effect of orientation for phase change material (pcm) - based heat sinks for transient thermal management of electric components. International Communications in Heat and Mass Transfer, 2007, Vol. 34, pp. 801-808

© 2024 Society of Thermal Engineers of Serbia. Published by the Vinča Institute of Nuclear Sciences, National Institute of the Republic of Serbia, Belgrade, Serbia. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution-NonCommercial-NoDerivs 4.0 International licence